START

Prepare a place to assemble the MAYA 2 cabinet. Make sure you have enough space for comfortable turning and the surfaces you will use are clean. We recommend using a carpet or blanket on which the parts can be safely assembled.

STEP 1

Unpack all parts. Check the number of parts included in the shipment.

STEP 2

STEP 3

If the quantities specified in the last three slides are correct, you can start assembling the furniture.

STEP 4

Start assembling from the part that will be the top of our cabinet. Let's call it TOP M2. Place the table top with the holes facing up on a flat surface and prepare carpentry pegs to insert them into the indicated holes. The dowels should be inserted to the end of the hole and protrude an equal distance from the countertop.

STEP 5

Then place the ECM pins in the threaded sockets in the countertop. You can screw them in by hand. In case of difficulty, use the tool.

STEP 6

The next step is to insert the ECM discs into the holes in the side walls. Each ECM eccentric disc has an arrow on its surface. Place the disc so that the arrow is visible and points in the direction of the pin hole. Only then will you be able to slide the wall onto the pins.

STEP 7

All walls, the so-called Side Panel Left/Right and Center Panel with embedded ECM eccentrics can be slid onto the pins. It is important that the rebate, i.e. the gap on the walls, is located on the side of the gap on the countertop to which we are adding the walls.

STEP 8

Once the walls are in place, use the tool to tighten the eccentrics. This action will press and connect the walls with the countertop. Use the Allen key included in the package to do this.

STEP 9

You can now insert the back of the furniture into the gaps in the walls and countertop. The parts are marked which is left and which is right. They may differ slightly in size. Remember to tuck the back all the way to the end of the slots.

STEP 10

Now insert further carpentry pins (9 pcs) and ECM eccentric discs (6 pcs) into the side walls. Remember that, as before, the arrows on the eccentrics should point towards the hole.

STEP 11

Now start preparing the bottom plate. Place the ECM pins in the threaded sockets in the countertop. You can screw them in by hand. In case of difficulty, use the tool.

STEP 12

It's time to assemble the bottom tabletop, i.e. the base of the furniture. Place the base plate on the eccentrics. Press the board so that it fits evenly onto the pins.

STEP 13

After placing the plate on the pins and pins of the eccentric, we can tighten the eccentrics by pulling the plate to the structure. Make sure each eccentric is properly tightened and there is a noticeable offset during tightening.

STEP 14

Carefully insert the steel legs into the holes in the boards. Insert the legs one by one, trying not to scratch the painted surface of the legs.

STEP 15

Tighten the legs with screws. Make sure there are feet at the base of each leg.

STEP 16

Turn the furniture upright by placing it on its legs. Be sure to ask someone for help.

STEP 17

The side walls of the furniture have holes drilled for mounting guides (runner). The guides should already be installed in the walls. Make sure this is the case. If not, fasten the guides with screws using small pre-drilled holes.

STEP 18

You probably already received furniture fronts with embedded hinges. However, if this did not happen, screw on the hinges according to the instructions in the illustration. This larger part is placed in the front openings. Use the attached screws that were in the hinge package.

STEP 19

We still have TIP-ON to install. First, place its base on the wall in the indicated place. Secure it with the screws included with TIP-ON.

STEP 20

It's time to assemble the fronts. Make sure the runners are not screwed on too tightly and you can move them up and down on the protruding screws. Place the hinges on the guides. The guides have a special hook that facilitates the installation of the hinge. First, slide the front with hinges parallel to the guide and then, after meeting resistance, press the hinge perpendicularly. You will hear a characteristic click. This is a sign that the hinge is installed correctly. Do this for each hinge. After installing them, determine the height at which the front should be so that the gaps between the front and the body are the same. Then tighten the screws in the guides. You can make further corrections by adjusting the BLUM hinge.

STEP 21

Method of attaching hinges to guides.

STEP 22

The last step is to install the shelves inside the cabinet. You can place the pins included in the package at any height inside the body. Use the holes drilled in the side walls. You need 4 pins to mount one shelf.

STEP 23

Insert the shelves into the cabinet by placing them on the pins.

Front adjustment

Adjusting the front on BLUM hinges is very simple. Follow the instructions above to set the fronts in the right position. Incorrect front adjustment may result in the cabinet not closing properly and the fronts rubbing against each other.

It's ready!

The MAYA 2 cabinet from TAMO is ready for use. More information about the use and care of wooden furniture can be found on our website at the following link: